Mannington MLG-33 Low Gloss Seam Sealer Kit – Vinyl Floor Repair Sealer
MLG 33 sealer (two- part seam sealer) is designed for Mannington Assurance II, Insight Plus, Realities, Primus and vinyl flooring with low-gloss urethane-based wearlayers. A properly sealed seam will be as strong as the surface of the floor covering, and will remain intact for the life of the floor. The Versatile Sealing Tip (VST-96) is included in this kit DIRECTIONS FOR USE: Prior to sealing, be certain all seams are clean, dry and free of adhesive contamination. Part B, which contains the de-glossing agent, must be shaken vigorously before blending with Part A. Empty entire contents of Parts A and B into the supplied applicator bottle. After securing the VST Tip to the applicator bottle, gently shake the bottle to mix the ingredients. After mixing, the bottle should stand until all trapped air bubbles have dispersed, typically 15 minutes. Prior to use, check the flow of the sealer on a scrap piece of flooring. Use the forefinger of one hand on top of the flat portion of the tip to guide and ensure proper fin penetration. Use the other hand to control sealer flow. Hold the bottle at approximately a 45° angle. Lightly squeeze the bottle and apply a uniform bead of sealer approximately 1/8″ wide centered on the seam cut. Note: Do not insert fin into the seam on Assurance II. For Assurance II use the applicator with the fin up. Be sure that the sealer is in contact with both sides of the flooring. Do not wipe the seam. Allow the sealed seam to dry before traffic can be allowed on the floor. Do not walk on or move heavy furniture directly over the sealer until it is fully dry. We recommend 24 hours. Mark the seam by placing a scrap piece of flooring along each side of the seam. MLG 33 cannot be saved for reuse. Safely discard any unused sealer. Carpets & More Our eBay Store Mannington MLG-33 Low Gloss Seam Sealer Kit – Vinyl Floor Repair Sealer Easy To Use Vinyl Flooring Seam Sealer Two-Part Seam Sealer Designed For Low-Gloss Urethane-Based Wear layers This Kit Includes Everything Needed To Properly Chemically Weld/Seal Your Vinyl Flooring Seams Creates a Seam As Strong As The Surface of The Floor Covering One Kit of MLG-33 Will Seal Approximately 70 Lineal Feet of Seams MLG 33 sealer (two- part seam sealer) is designed for Mannington Assurance II, Insight Plus, Realities, Primus and vinyl flooring with low-gloss urethane-based wearlayers. A properly sealed seam will be as strong as the surface of the floor covering, and will remain intact for the life of the floor. The Versatile Sealing Tip (VST-96) is included in this kit DIRECTIONS FOR USE: Prior to sealing, be certain all seams are clean, dry and free of adhesive contamination. Part B, which contains the de-glossing agent, must be shaken vigorously before blending with Part A. Empty entire contents of Parts A and B into the supplied applicator bottle. After securing the VST Tip to the applicator bottle, gently shake the bottle to mix the ingredients. After mixing, the bottle should stand until all trapped air bubbles have dispersed, typically 15 minutes. Prior to use, check the flow of the sealer on a scrap piece of flooring. Use the forefinger of one hand on top of the flat portion of the tip to guide and ensure proper fin penetration. Use the other hand to control sealer flow. Hold the bottle at approximately a 45° angle. Lightly squeeze the bottle and apply a uniform bead of sealer approximately 1/8″ wide centered on the seam cut. Note: Do not insert fin into the seam on Assurance II. For Assurance II use the applicator with the fin up. Be sure that the sealer is in contact with both sides of the flooring. Do not wipe the seam. Allow the sealed seam to dry before traffic can be allowed on the floor. Do not walk on or move heavy furniture directly over the sealer until it is fully dry. We recommend 24 hours. Mark the seam by placing a scrap piece of flooring along each side of the seam. MLG 33 cannot be saved for reuse. Safely discard any unused sealer.
Mannington MSS20 Standard Gloss Vinyl Flooring Seam Sealer Pint with Applicator
Mannington MSS 20 Standard Gloss Vinyl Flooring Seam Sealer Kit contains 1 Pint + 4 Fl Oz applicator bottle. It is designed for seam sealing all resilient vinyl flooring products with a vinyl wear layer. A properly sealed seam will be as strong as the surface of the floor covering and will remain intact for the life of the floor. The Applicator Bottle contains a tip cleaning pin and the Versatile Sealing Tip. Intended to be used for liquid-weld seam sealing of vinyl flooring. Ergonomic design with a specially engineered tip to help apply the appropriate amount of seam sealer while completely penetrating the seam cut for all Commercial sheet flooring applications. Carpets & More Our eBay Store Mannington MSS 20 Standard Gloss Vinyl Flooring Seam Sealer Kit (1 Pint) with Applicator Bottle Easy To Use Pint Size Vinyl Flooring Seam Sealer Kit With Applicator Bottle – Standard Gloss Repair / Seal Minor Cuts & Chemical Weld Vinyl Floor Seams For Use On All Vinyl Flooring With A Vinyl Wearlayer – Not For Use On Vinyl With Urethane-Based Wear Layers No Mixing, 1 Part, Standard Gloss – Will Seal Approximately 400-600 Lineal Feet of Seams Comes with 4-ounce bottle with versatile vinyl flooring seam sealing tip & cleaning pin Mannington MSS 20 Standard Gloss Vinyl Flooring Seam Sealer Kit contains 1 Pint + 4 Fl Oz applicator bottle. It is designed for seam sealing all resilient vinyl flooring products with a vinyl wear layer. A properly sealed seam will be as strong as the surface of the floor covering and will remain intact for the life of the floor. The Applicator Bottle contains a tip cleaning pin and the Versatile Sealing Tip. Intended to be used for liquid-weld seam sealing of vinyl flooring. Ergonomic design with a specially engineered tip to help apply the appropriate amount of seam sealer while completely penetrating the seam cut for all Commercial sheet flooring applications.